ELECTRICAL FEATURESPOWER SUPPLY Voltage: ...
1 •2 •3 •4 •5 •6 •LEFT SPEAKERAmplifi er left channel (Left) power ouput. Connect speakers cables to this output according to indicated polarity. If yo
1 •2 •3 •4 •5 •6 •7 •- POWER (GROUND)Terminal block for the amplifi er power supply negative pole connection. Connect the battery negative cable or the
1 •2 •3 •4 •5 •OUT MODEIt permits to confi gure the amplifi er in STEREO or MONO.If you put Out Mode control on STEREO, PRE IN LEFT and RIGHT inputs sig
ASC – Amplifi er Status Controller UnitASC handles all the amplifi er functions, except sound.It has a microprocessor and through its Status Display, it
- 14 -SIDE HANDLES REMOVALOWNER’S MANUAL6a. Unscrew the 6 screws which fi x the glass panelb. Before closing the product, make sure there are no
- 15 -b. Remove the side handle above power supply terminal blocks: seec. Lift the plexiglass panel which protects power supply terminal blocksd.
HI POWER4 10A blade mini-fusesHI CURRENT4 15A blade mini-fuses- 16 -Pre-settingd. Find the 4 blade mini-fuses and set them in the confi guration you l
f. Mount the side handle back: see g. Reassemble the glass panel: see - 17 -Pre-settingCaution!: if you change BIAS switch setting, idling curren
- 18 -a. Remove the glass panel: see b. Remove the bypass module by unfastening the two screws which secure it inside the product.c. Select the
... page 13... page 12... page 11... page 10... page 14a. Unscrew the six screws wh
- 19 -a. Accessories supplied with HV ventiAudison stickerINOX “CARD”Certifi cate of property with HV venti serial numberConnections covering grilles a
- 20 -c. If you like to change DUAL POWER confi guration in order to set it on “HI POWER”: see d. If you like to change DUAL BIAS confi guration in o
- 21 -f. NON-PROJECTING or SEMI-PROJECTING installationHOW TO USE THE ADHESIVE DRILLING TEMPLATENON-PROJECTING FIXINGSEMI-PROJECTING FIXINGRecommende
- 22 -g. Remove the amplifi er fi xing plateh. Secure the fi xing plate through 8 screws at leastScrews diameter must be 4mm (.15 inches) max.INSTALLATIO
- 23 -i. Secure the amplifi er to the fi xing platej. Connect signal cables: see k. Connect power supply cables: see l. Amplifi er calibration: see
- 24 -MAINTENANCEOWNER’S MANUAL12a. Fans protecting fi lters cleaningb. Cooling ducts cleaningThis is recommended every time the amplifi er is removed f
Safety precautions• The vehicle electric system must have 12VDC voltage with negative to ground. Make sure your car has it in order to avoid any dama
1 • PROJECT PURPOSEAudison has always pursued the best audio reproduction in all of its products.The creation of the HR100 in 1991 occurred simultaneo
The fi nal power stage uses an innovative topology, which aims at increasing Class “A” polarization as much as possible.The whole input circuit is bala
JFET differential input stage (available in PRE ON confi guration).Selectable two level input gain structure adjusted (available in PRE ON confi guratio
value on every output device is possible, keeping stable the total current absorbed by the amplifi er when in idling status.All this results in the inc
Indications shown on the Status Monitor are:POWER ON: The amplifi er turn on status.HI POWER: When on Dual Power is in Hi Power mode, if turned off it
Drivers were attached to it, while the preamplifi er is connected to it through copper bars.The fan is managed by the ASC unit, permitting it to quickl
Kommentare zu diesen Handbüchern